Dobrodošli u Player svet! Prijavi se ili Registracija

Svetogorska 9: +381 11 3347 615
+381 11 3347 442
+381 11 3347 883
Sarajevska 68-70: +381 11 2688 067
+381 11 2688 068
+381 11 2688 069
Južni Bulevar 1a: +381 11 4065 432
+381 64 64 70 100
Futoški put 1: +381 21 3010 626
+381 21 3010 627
Pantelejska 53: +381 18 4200 878
+381 64 647 0101
Njegoševa 16: +387 55 209 104 +387 55 209 987 +387 66 222 070


Proizvođač: FBT VERTUS MLA 801A
Dostupnost: Nema na stanju
Šifra Proizvoda: 65988

It is possible to emulate the directivity of a classic J-form line array, either curved or straight. Starting from the analysis of known line array systems with digital directivity control (columns with small wide-band speakers) or mechanical directivity (all systems with inclinable cabinets that form a curved or straight J-form array), we decided to condense into one product the advantages of both types of controls, while at the same time surpassing their traditional limits.

3446 € € 2499

The principle behind the operation of MLA is based on the combined mechanical/digital control of directivity. Digital allows for the control of directivity up to around 4KHz; mechanical, assisted by digital, from 4KHz to over 15KHz. This enables the system to reach the following targets:

  •  An aesthetically non-intrusive vertical column that is readily adaptable to any environment
  • Control of full-range directivity from the lower frequencies (depending upon the length of the column) up to and over 15KHz
  • Elevated SPL, thanks to the usage of a compression drivers e wave guide at high frequencies
  • LImited number of transducers and therefore DSP channels and amplifiers associated with “no compromise” systems of exclusively digital steering with drastic reduction of cost.

Mixed Control Active Line Array 8 x 50W - 139dB SPL

  • 8-way active HF Line Array Column, with digital/mechanical directivity aiming
  • 8 x 0,75” (20mm) B&C neodymium drivers with 1” (25 mm) voice coil on wave guide
  • 1.8KHz to 20KHz frequency response
  • 8 class D 50Wrms amplifiers for a total of 400W power
  • Completely controllable directional features, through control switches on the back panel or through PC software and dedicated network
  • Revolutionary combined aiming digital/ mechanical full-range system from +5 a -25° with included lobe width between 5° and 25/40°
  • 8 hybrid stepped motor controlled by a microprocessor for the mechanical aiming of wave guides
  • PC/Slave function for aiming control via PC or other MLA module
  • Frontal status LED
  • DSP processor for the management of digital aiming and signal processing, 4 available presets
  • Control panel with XLR input and XLR link, XLR HP-filtered output, volume, presets, 7-step angle aiming, 8-step lobe width, HP filter, ground-lift, RJ45 in/out for RS- 485 network, screw connectors for in/ out audio and for installation
  • 90° Digital-Mechanical controlled dispersion
  • Extruded-aluminum powder-coated cabinets. Superior latching system as well as inferior for the MLA series, allowing for great component modularity
  • Standard white finish RAL 9016
Built-in amplifier LF/HF: 8x40 W RMS
Built-in amplifier peak LF/HF: 8x100 W
Frequency response: 1.8Hz - 20Khz -6dB
High frequency driver: 8 x 0.75 - 1 coil - neodymium inch
Maximum SPL cont/peak: 135/139 dB
Dispersion: 90° x Digital-Mechanical controlled H x V
Steering Angle: +5/-25 V
Beamwidth Angle: 5/40 V
Input impedance: 22 Kohm
Crossover frequency: 1.8 KHz
Ac power requirements: 300 VA
Input connector: XLR with loop, SUB out
Power cord: 5/16.4 mm/inch
Net Dimension (WxHxD): 240x625x242 / 9.5x24.6x9.52 mm/inch
Net weight: 18/39.7 kg/lb
Transport Dimension (WxHxD): 320x725x322 / 12.6x28.54x12.67 mm/inch
Transport weight: 20.5/45.2 kg/lb

Nazad na kategoriju Line Array